YOUR BUYING COMPANION
Get the right fit for your setup.
Three useful checks before you order. Work through them at your own pace.
01Check the fit before ordering
Measure the mounting area and check that the surface curvature permits the strip to lie against it. Adhesive suitability depends on paint, coating, cleanliness, temperature and condition. Test a discreet area and follow vehicle-finish and adhesive care instructions. Do not cover sensors, lights, reflectors, plate markings, vents or other required features. Do not expect cosmetic trim to prevent collision damage or repair an already damaged panel.
02Choose the right configuration
Review the pack, color and other options. The selected configuration and price identify what goes in your cart; the photograph does not establish pack quantity.
03Plan the first use
Read the setup and care guidance below. For a larger supply order, check one item against the actual fit and intended task before distributing the rest.
Use these checkboxes to track your review. Confirm the selected contents and any fitting or care requirements before ordering.
WHAT IT IS · HOW IT WORKS
A red accent for a suitable bumper surface.
Add two long red trim strips to a compatible vehicle surface. The source lists each strip at approximately 15.3 inches long by 1.5 inches wide, with flexible rubber construction and adhesive backing. Check the bumper shape, finish and installation area before peeling the backing. This is cosmetic trim for suitable surfaces, not a replacement bumper or a crash-protection component.
Two strips in one order
One pack supplies two red trim strips. The approximately 15.3 × 1.5-inch dimensions apply to each strip, not the combined length of both.
Compare length and curvature first
Hold the strip against the proposed area with its backing intact. Check both the endpoints and the full contact area; tight curves, textured surfaces and irregular edges may prevent a suitable fit.
Prepare before peeling
Start with an intact surface that is clean and dry according to its care instructions. Position carefully before peeling and pressing. Installation temperature and any adhesive setting time should follow the supplied adhesive instructions.
Cosmetic trim has a limited role
The flexible strip adds a red accent and a layer of material at its mounting point. It is not a structural bumper component, a collision restraint or a guarantee against scratches or impact damage.
A CLOSER LOOK
Two strips in one order
One pack supplies two red trim strips. The approximately 15.3 × 1.5-inch dimensions apply to each strip, not the combined length of both.
MAELINE · PRACTICAL GUIDE
READY TO USE
Measure and inspect the panel
Park safely. Compare the approximately 15.3 × 1.5-inch strip with the proposed location. Keep sensors, lights, plate information, vents and required features clear.
GET SET UP
How to use it.
- 1
Measure and inspect the panel
Park safely. Compare the approximately 15.3 × 1.5-inch strip with the proposed location. Keep sensors, lights, plate information, vents and required features clear.
- 2
Trial-position with the backing on
Check the complete contact area and curvature. Do not cut, stretch or force the strip unless the supplied instructions permit it.
- 3
Prepare and attach
Follow the finish and adhesive instructions to clean and dry the surface. Peel the backing only after confirming the position, then press along the intended contact area without damaging the finish.
- 4
Check adhesion and future removal
Follow any supplied setting-time guidance before washing or exposing the trim to demanding conditions. Inspect for lifting edges. When removing, use a method suitable for the paint and adhesive; residue or finish damage cannot be ruled out.
A GOOD FIT FOR
Adding a red cosmetic accent to a suitable smooth vehicle panel where the strip dimensions and adhesive application have been checked.
Measure the mounting area and check that the surface curvature permits the strip to lie against it. Adhesive suitability depends on paint, coating, cleanliness, temperature and condition. Test a discreet area and follow vehicle-finish and adhesive care instructions. Do not cover sensors, lights, reflectors, plate markings, vents or other required features. Do not expect cosmetic trim to prevent collision damage or repair an already damaged panel.
Get help with a larger order →PRODUCT FACTS
- Included
- 2 red adhesive trim strips
- Approximate size per strip
- 15.3 × 1.5 inches
- Source-listed material
- Rubber
- Attachment
- Adhesive backing
- Use
- Cosmetic trim on a suitable vehicle surface
- Not a replacement bumper
- No structural protection claim
- Vehicle and tools
- Not included
BEFORE YOU ORDER
Useful answers.
How many strips are supplied?
Two red adhesive trim strips. Cart quantity two supplies four strips.
What size is each strip?
Approximately 15.3 inches long by 1.5 inches wide, as listed by the source. Measure the actual mounting area before ordering.
Will they fit every vehicle?
No universal fit is established. The panel shape, surface texture and available contact area must suit the strips and their adhesive backing.
Are they replacement bumpers?
No. They are decorative adhesive trim strips, not structural bumper parts or crash-protection equipment.
Is adhesive backing included?
The source specifies adhesive backing on the strips. Additional surface-preparation products or installation tools are not listed as supplied.
Can they cover a parking sensor?
Keep sensors, lights, reflectors, required plate markings and other vehicle functions unobstructed.
Will removal damage the paint?
Paint condition and adhesive compatibility vary. Test and follow appropriate removal instructions; residue or finish damage cannot be ruled out.
Can these prevent all scratches or collisions?
No. The strips do not guarantee damage prevention. Their position and material do not replace careful use, correct vehicle repairs or structural protection.